Categories
- Turbochargers
- Turbo Flanges / Adapters
- Turbo Gaskets
- Accessories
- Blow Off / Bypass Valves
- Boost Controllers
- Clamps
- Exhaust
- Fittings & Lines
- Fuel Supply
- Intercooler Pipes & Parts
- Intercoolers
- Pipes / Bends / Elbows /Tubes
- Turbo Accessories -Other
- Turbo Silicone Couplers
- WasteGates
- MAZDA
- MITSUBISHI
- SUBARU
- VW / Audi
- CLEARANCE ITEMS
Reviews [more]
Newsletter
English
Boost Cut Killer Module, Mazdaspeed6 /Mazdaspeed3/CX7
Boost-Cut Killer module for Mazdaspeed6 /mazdaspeed3/CX7 2.3L Turbo engine. Eliminates the ECU induced "boost-cut" condition when boost on the engine is raised beyond factory stock settings. The module has been designed to bolt on, inline with the factory MAP sensor using the simple hardware provided. No other changes or tweaks are necessary. Works well with both stock turbo with bolt-ons and big upgraded turbo setups.
While we have found that this device works very well with the stock fuel system to retain good air/fuel ratios when boost levels are raised, the factory fuel system does have a limit and can only support so much boost/HP. The peak boost cut limit is almost completely removed with this modification so there will be no safeguard against overboost. You must closely monitor your air/fuel ratio and boost levels upon installation of this device to ensure that you are operating the engine in the safe running zone.
$69.95
GReddy 1" Type RS Blow Off Valve Recirculation Kit
This Greddy 1" re-route adapter screws into the outlet of your GReddy Type-RS blow off valve & replaces the stock horn. It allows a hose to be clamped on so the "blown off" boost pressure can be redirected back into your turbo's intake. Helps reduce compressor surge even more and reduces turbo lag for quicker spool up between shifts. Has a Rolled Lip to hold Hose Strong Under High Boost.
Fits Greddy Type RS BOV, made of billet aluminum. 1.25" Recirculation adapter & the colored silicone hose also available on our site. BOV not included.
$18.98
GReddy 1.25" Type RS Blow Off Valve Recirculation Kit
This Greddy 1.25" re-route adapter screws into the outlet of your GReddy Type-RS blow off valve & replaces the stock horn. It allows our 1.25" hose to be clamped on so the "blown off" boost pressure can be redirected back into your turbo's intake. Helps reduce compressor surge even more and reduces turbo lag for quicker spool up between shifts. Has a Rolled Lip to hold Hose Strong Under High Boost.
Fits Greddy Type RS BOV, made of billet aluminum. 1" Recirculation adapter & the colored silicone hose also available on our site. BOV not included.
$18.98
GReddy BOV Adapter - Stock Mazdaspeed 6
For Mazdaspeed 6. Allows GReddy BOV to bolt on to the stock BOV location.
Blow off Valve adapter allows you to easily mount the Greddy Type S/RS/R & RZ blow off valve to Mazdaspeed6 stock location on the Top Mounted Intercooler. For atmospheric use by ordering the additional billet plug for the stock inlet pipe or recirculation use by ordering the additional recirc adapter to route back into the intake pipe. Does Not Include BOV.
Includes mounting hardware & O-ring.
$25.90
Greddy Type S, R, RS, RZ BOV Flange - Evo 8
This Adapter Flange allows the GReddy Type S/R/RS & RZ blow off valves to bolt on to the Evo 8, using the stock hose & clamp. Very EZ, 2 minute installation. CNC machined form billet aluminum. Fits all of the GReddy valves.
$33.90
HKS BOV Adapter - Stock Mazdaspeed 6
For Mazdaspeed 6. Allows HKS BOV to bolt on to the stock BOV location.
Blow off Valve adapter allows you to easily mount the HKS BOV to the Mazdaspeed 6 stock location on the Top Mounted Intercooler. For atmospheric use by ordering the additional billet plug for the stock inlet pipe or recirculation use by ordering the additional recirc adapter to route back into the intake pipe. Does Not Include BOV.
Includes O-ring.
$41.00
HKS BOV Flange Lower Weld On Section -Aluminim
This is the lower weld on section for use with our HKS 2 piece Blow Off valve flanges. This piece welds to the intercooler pipe it's self. Perfect if you already have one of our HKS weld on flanges & need to put the BOV on a new application.
For use with aluminum intercooler pipes.
$16.00
HKS BOV Flange Lower Weld On Section -Steel
This is the lower weld on section for use with our HKS 2 piece Blow Off valve flanges. This piece welds to the intercooler pipe it's self. Perfect if you already have one of our HKS weld on flanges & need to put the BOV on a new application.
For use with steel intercooler pipes.
$16.00
HKS SSQV BOV Flange - Evo 8
This Adapter Flange allows the HKS SSQV blow off valve to bolt on to the Evo 8, using the stock hose & clamp. Very EZ, 2 minute installation. CNC machined form billet aluminum.
$38.90
Turbo Oil Return/Drain Fitting for Mazdaspeed 3
Turbo oil return flange, engine side, Made in the USA. CNC machined aircraft aluminum flange fitting. Bolts to Mazdaspeed3 engine side to connect -10 braided return line. 2 bolt flange bolts to oil return port on Mazdaspeed 3 engine block. Out of the flange is an integrated -10 AN/JIC flare male.
$28.00
T3 T3/T4 Internal Wastegate Flange w/ Swing Valve
Made in the USA, UIWG style turbo discharge flange with integrated swing valve & ovalized opening. Fits Standard T3 5-bolt Ford type turbo exhaust housings commonly found on many turbo's including T3/T4 units. Flange is just over 1/2" think & works well with our UIWG style transition found in the recommended items on this page.
$90.00
Oil Feed Fitting w/ Restrictor - T & Big GT Turbos .065
Oil inlet restrictor for T series turbochargers. Installed at the oil inlet on turbo to reduce max oil pressure going into the turbo to prevent turbo seal damage due to excess pressure. Input is 1/8" NPT male and output is 1/8 NPT female. restrictor size is .065
For use with Many T turbos including:
T3, T3/T4, T04, T04B, T04ET, 60-1, T72 GT4088R, GT4094R, GT42R, GT42RS, etc.
-6 AN To 3/8" OEM Quick Connect O-Ring Fitting
3/8" Male quick connect o-ring fitting to -6 AN. Allows ease of transition from -6 AN to the newer O-ringed squeeze and release type fittings found on many newer fuel systems and emissions devices. Great for installing an after market performance fuel filter, fuel pressure regulator, etc.
$15.00
-6 AN To 5/16" OEM Quick Connect O-Ring Fitting
5/16" Male quick connect o-ring fitting to -6 AN. Allows ease of transition from -6 AN to the newer O-ringed squeeze and release type fittings found on many newer fuel systems and emissions devices. Great for installing an after market performance fuel filter, fuel pressure regulator, etc.
$15.00
Subaru Downpipe to Turbo Flange
CNC machined mild steel downpipe flange for the stock turbo on all Subaru EJ2X engines. Allows for custom downpipes.
$24.00
Volvo & Mitsubishi Adapter - T3 Turbo to Stock Manifold
Made In The USA::
This Flange adapter allows any T3 flanged turbo to bolt up to the Volvo manifold that use the Mitsubishi TD0X turbos (Models 750, 850, V70, C70, etc.) The adaptor sits inside the flange on the manifold & fills the space, achieving a leak free seal.
Allows the use of many new turbos such as, T3, T3/T4, GT28RS, GT2871R, GT2876R, GT3071R, GT3076R, GT30R, GT3040R, GT35/40R, GT35R)
$48.30
Downpipe Flange For Mazdaspeed 3 & 6 - Stock Turbo
Made In The USA::
This is a downpipe Flange for the stock turbo found on the Mazdaspeed 3 & 6. Bolts to the back of the turbo & allows you to create your own custom downpipe. 3/8" think to prevent warping. CNC machined.
$24.00
Downpipe V-band Adapter For Mazdaspeed 6 - Stock Turbo
This is a downpipe V-band adapter for the stock turbo found on the Mazdaspeed 6. One side is flanged to fit the back of the stock turbo or stock downpipe while the other side is a 3.00" V-band. Nice formed stainless transition for smooth flow. CNC machined & fully TIG welded.
$95.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
Garrett 40mm External Wastegate Kit GVW-40 SILVER
Garrett 40mm GVW-40 External Wastegate ...
$317.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
New Products For May
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
Himni Polyurethane Motor Mounts -STREET/RACE Mazda RX-7 93-00
Himni Racing Polyurethane FD RX-7 Motor...
$99.90
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
2A Himni Polyurethane Motor Mounts -STREET/RACE Mazda RX-7 86-92
Himni Racing Polyurethane FC RX-7 Motor...
$98.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
Himni SS Master Engine Nut & Bolt Kit, 93-99 Mazda RX-7
Master engine hardware kit. Replaces mo...
$84.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
Himni SS Master Engine Nut & Bolt Kit, 87-91 Mazda RX-7
Master engine hardware kit. Replaces mo...
$78.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
HR GT Turbo Water / Oil Installation Kit : GT25R - GT35R
For use with All small to mid frame Gar...
$78.00
12mm Barb To -6 AN Female Fitting
12mm hose barb fitting To -6 AN female. Also used on Subaru turbo kit for coolant out.
$15.00
86-91 Mazda FC RX-7 SS Braided Oil Cooler Line/Hose Kit
Made in USA. The Himni Racing FC RX7 St...
$215.00
Featured Products
Himni Racing Polyurethane FD RX-7 Motor...
Himni Racing Polyurethane FC RX-7 Motor...
Bestsellers
Customer Testimonials
Oh my goodness! Fastest shipping I have ever experienced from the US! Many thanks
- James S. Ontario, Canada...
Read More ->
Great Customer Service!!
You guys are an example to every Shop! MANY THANKS for all your help!
- Kenneth B of Mosta, Malta...
Read More ->
LATEST PRODUCTS
Garrett 40mm GVW-40 External Wastegate K...
-
Garrett 40mm GVW-40 External Wastegate K...
EXTRAS
SUPPORTS
© Copyright 2005-2023 Himni Racing. All Rights Reserved.