Custom machined Oil inlet / feed fitting for Garrett GT Ball Bearing Turbos. Screws right into the turbos listed below & works with any -4 AN line. Has a built-in oil restrictor to supply the GT turbos the amount of oil they need while keeping your oil pressure up. Too much oil feed can blow the turbo's seals. **Also for use on the Garrett T ball bearing turbos**
Note:: The use of this fitting / restrictor is highly recommended. The Garrett GT series turbos do not require as much oil to be fed to the bearings, compared to the old T Series turbos.
The benefits of use include:
Protects the turbo's seals from excessive oil feed.
No more oil pressure drop. (allows your engine to maintain a higher oil pressure)
A simple & secure way to attach a standard -4 AN oil feed line.
Fits the turbos below:
GT28R, GT28RS, GT2871R, GT2876R / GT25/40R, GT30R, GT3071R, GT3076R, GT3040R, GT35R & More.
Oil inlet restrictor for T series turbochargers. Installed at the oil inlet on turbo to reduce max oil pressure going into the turbo to prevent turbo seal damage due to excess pressure. Input is 1/8" NPT male and output is 1/8 NPT female. restrictor size is .065
For use with Many T turbos including:
T3, T3/T4, T04, T04B, T04ET, 60-1, T72 GT4088R, GT4094R, GT42R, GT42RS, etc.
EVO 8 Oil Feed adapter. Cyl Head to -4 Male AN Flair. Fits directly to the original oil feed source on the cylinder head & allows for the use of any -4 an oil line. . Remove the stock oil feed line, install new fitting, and use new -4 AN line. Makes installing a turbo up-grade EZ.
$17.401.8T oil feed adapter simplifies installation of aftermarket oil lines. Adapts to the stock oil feed line source at the oil filter housing to -4 Male AN Flair.
Allows any -4 oil feed lines to be used on the 1.8T engine without tapping into the pressure port. Remove the stock oil feed line, install new fitting, and use new -4 AN line.
$15.29Himni Racing SS oil feed line kit for use with Garrett 'GT BALL BEARING SERIES' Turbochargers only. (GT25R-GT35R)
Other kits available for the following turbo configurations are also found in our catalog. Applications for:
- Stock 87-92 Turbo II TurboCharger
- T Series TurboChargers
- Large Garrett GT Series TurboChargers (GT40R-up)
NOTE, pick engine type from menu. We have kits available for the following engines:
Mazda 13BT Turbo II (87-92)
Mazda 13B-REW (93-99)
Mazda 13B-RE (2 rotor Cosmo)
Mazda 20B (3 rotor Cosmo)
The Himni Racing Stainless Steel Braided 'GT SERIES' Mazda RX-7, Turbo Oil Feed Line Kit is for use with many of the popular GT series turbos. (list seen below) Direct bolt-on for all Mazda RX-7's rotary engines. (pick your car / engine from the menu) Our RX-7 oil feed kits are top of the line! The Teflon coated core will insure a long life & superior oil resistance. Kit Includes Everything needed::: -4 SS line with ends, restrictor & all required fittings. Allows you to utilize the stock turbo oil feed port in the front housing & even uses the stock bolt & copper washers. A very clean, leak free fit at any pressure you throw at it. Because a restrictor is included, there's no need to worry about damaging the seals in your Garrett GT Turbo, while still providing it with all the oil it needs. Replaces the whole stock line, quickly and easily.
Works With the following Garrett Turbochargers:
GT25R, GT28R, GT28RS, GT2871R, GT25/40R, GT2876R, GT3071R, GT30R, GT3076R, GT3040R, GT3082R, GT3582R, GT35/40R, GT35R, GT35R T4 & more.
Banjo fitting kit for coolant / water connections on Garrett GT25R/GT28R Turbochargers. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT28RS & GT2871R Turbochargers. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT2876R & GT3071R Turbochargers. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT30R. GT3076R Turbochargers. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT3082R, GT3040R Turbocharger. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT3071R Turbocharger. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT3076R-WG Turbocharger. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT25R Turbocharger. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.50Banjo fitting kit for coolant / water connections on Garrett GT35R, GT3582R Turbocharger. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
Note:: 2 of these kits required per turbo.
$16.5014mm Machined aluminum Banjo fitting kit. Great for turbo water & other connections. 14mm banjo bolt to 1/4" NPT - Very flexible when used with 1/4" NPT to -6 AN fitting.
Includes:
14mm aluminum banjo fitting
1 banjo
2 copper washers.
For coolant/ water connections, it fits the turbos below.
GT25R, GT28R, GT28RS, GT2871R, GT2876R, GT30R, GT3071R, GT3076R, GT3040R, GT35R, GT3582R
2 of these kits required per turbo when used as water fittings
Banjo fitting kit is good for use with water, oil & fuel. Works with standard 3/8" hose. The fitting screws to the turbo & the hose simply slips on to the barb, then clamps for secure, leak-free fit. Machined aluminum fitting, steel bolt, copper gaskets. Commonly used for coolant / water connections on Garrett GT25R-GT35R Turbochargers.
Includes::::
14mm banjo fitting
1 banjo fitting
2 copper washers
-3 AN To 1/8" NPT 45 Degree Fitting. " Male to Male" Suitable for turbo oil feed lines, water & fuel.
$6.80-3 AN To 1/8" NPT Straight Fitting " Male to Male" Great for turbo oil feed lines, water & fuel.
$6.80-4 AN To 1/8" NPT 45 Degree Fitting. " Male to Male" Suitable for turbo oil feed lines, water & fuel.
$8.25-4 AN To 1/8" NPT 90 Degree Fitting " Male to Male" Great for turbo oil feed lines, water & fuel.
$10.50-4 AN To 1/8" NPT Straight Fitting " Male to Male" Great for turbo oil feed lines, water & fuel.
$8.40Turbo Oil return / drain fitting. Fits both our GT series & T series turbo oil return flanges with 1/2" female NPT threads.
Threaded to a male 1/2" NPT with a 45 degree 5/8" hose barb. Works with any 5/8" or -10 an line / hose. Great for use with turbo oil return flanges that are threaded to a 1/2" NPT
$19.99Turbo Oil return / drain fitting. Fits both our GT series & T series turbo oil return flanges.
Threaded to a male 1/2" NPT with a Straight 5/8" hose barb. Works with any 5/8" or -10 an line / hose. Great for use with turbo oil return flanges that are threaded to a 1/2" NPT
$8.96-10 AN To 1/2" NPT Straight Fitting " Male to Male" Suitable for oil , water & fuel. Works great with our turbo oil return / drain flanges & lines.
$7.00-10 AN To 1/2" NPT 45 Degree Fitting. " Male to Male" Suitable for oil, water & fuel. Works great with our turbo oil return flanges & lines.
$10.90-10 AN To 1/2" NPT 90 Degree Fitting " Male to Male" Suitable for oil, water & fuel. Wroks great with our turbo oil drain flanges & lines.
$11.40Metric fitting:: 14mm male (1.5 pitch) to male 6 AN Flare, with sealing Washer. Provides easy way to connect to stainless Steel braided type lines with #6 AN hose ends. Great for use with coolant, oil, & fuel. Commonly used as a water fitting on Garrett ball bearing turbos.
When used as a water fitting, it fits: GT25R, GT28R, GT28RS, GT2871R, GT2876R, GT2540R, GT3071R, GT30R, GT3076R, GT3040R, GT3082R, GT35R, GT3582R, GT3540R.
$15.90Metric fitting:: 16mm male (1.5 pitch) to male 6 AN Flare, with sealing Washer. Provides easy way to connect to stainless Steel braided type lines with #6 AN hose ends. Great for use with coolant, oil, & fuel. Commonly used as a water fitting on Garrett ball bearing turbos & other T series turbos.
$15.90Metric fitting:: 18mm male (1.5 pitch) to male 6 AN Flare, with sealing Washer. Provides easy way to connect to stainless Steel braided type lines with #6 AN hose ends. Great for use with coolant, oil, & fuel. Commonly used as a water fitting on Garrett ball bearing turbos.
When used as a water fitting, it fits:
GT40R (GT4088R) GT42R , GT42RS & other large frame T series turbos including T70 , T72, etc.
Also fits the Bosch 044 fuel pump as the inlet fitting.
$15.90Hands down, best supplier of parts ANYWHERE...PERIOD. Fast service and very knowledgeable staff helped our build and continues to be a resource when......
Read More ->
You guys are an example to every Shop! MANY THANKS for all your help!
- Kenneth B of Mosta, Malta...
Read More ->
Garrett 40mm GVW-40 External Wastegate K...
Garrett 40mm GVW-40 External Wastegate K...
© Copyright 2005-2023 Himni Racing. All Rights Reserved.