Apexi Power Intake - Subaru WRX ___ This intake has dual stainless steel funnels to direct intake air smoothly into the throttle body. The air filter is made of an unrestricted race quality element and has one funnel at the top of the filter and one funnel at the base. Apex engineers noticed in tests that when the vehicle sucked in air from the side, an area of wind turbulence occurs in the middle of the filter. To cure this problem, a funnel at the top of the filter was added to channel the air down to the base of the filter. A separate funnel at the base of the filter ensured the smooth transition of air form the atmosphere into the intake pipe. Both funnels are constructed of a high quality polished SUS 304 stainless steel and the craftsmanship only found in Apex products.
$115.00The ARC super induction box focuses on low, mid, and high engine response. When stepping on the gas, in between the cleaner and the intake manifold is unused air. ARC invented this Induction box to utilize the unused air and give it better airflow and better response. This unit is also a direct bolt on. The replacement filters and most popular Japanese vehicle applications are now available.
$354.98The Carbon Fiber Radiator Shroud is designed to push more air through your radiator, making your WRX run much colder. When your vehicle is motion, air goes through the grill and is pushed across the radiator. Some air escapes around the top and bottom, limiting the efficiency of the radiator. Fits Subaru WRX/STi 02+ -Retail: $129.95
$106.90This intake is the latest generation of Airinx intakes. Sandwiched between Greddy's new dual chrome ABS spiral cages is a special double-ply element. The element uses 2 layers of 3 dimensional urethane foam (with different textures) to increase the filtration and maximize intake air flow. The outer ply has large opening while the inner rough layer is made up of a fine foam. The outer cage is a spiraled straight-fin design, which helps promote air volume. The chrome finish can dress up any high performance engine compartment. Fits Subaru WRX Turbo
$139.90The addition of a GReddy intercooler is an excellent way of safely increasing horsepower. By reducing the engine's inlet temperatures, a denser air charge will enter the engine; this will make more power at the same boost level. Greddy's vehicle specific kits include all the necessary mounts, piping and hoses required to install the kit. All kits are designed to give maximum cooling capacity while allowing for minimal pressure drops. This is achieved by properly sizing the core and tuning the internal core with either a V-spec. core or with a different inner fin pattern in the R-spec core. All cores are an air-to-air, tube and fin design that does not require any specialized liquid plumbing. The end of the cores are capped off with smooth flowing heavy-duty cast aluminum endtanks.
Note: Picture may not reflect actual FMIC package for your vehicle.
$899.90RED__Built for performance and show, the K&N Typhoon Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intakes come in one of three designs; cold air intakes (CA), short ram intakes (SR), or complete cold air (CCA) intakes which can be configured as either a cold air intake or a short ram intake. Some Typhoon's have high quality finish options including polished aluminum (part ends with TP), powder coated blue (part ends in TB), powder coated red (part ends in TR), and powder coated silver (ends in TS) among others.
K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction allowing more air flow to your engine. More air means more usable power and acceleration throughout the engine's RPM range.
$229.90The gas (we suggest CO2) sprays directly on your intercooler to lower the intercooler temp to well below freezing. The result is a tremendous drop in intake temperatures. Dyno tests have seen increases of over 50+ horsepower! Allows you to cool of your Intercooler in between races, to allow for a more efficient setup and increasing HP. Kit includes: intercooler sprayer bar, all necessary hoses and fittings, switch, and wiring kit. Includes 15LB Bottle, Retail: $599.00
$443.90The gas (we suggest CO2) sprays directly on your intercooler to lower the intercooler temps to well below freezing. The result is a tremendous drop in intake temperatures. Dyno tests have seen increases of over 50+ horsepower! Allows you to cool of your Intercooler in between races, to allow for a more efficient setup and increasing HP. Kit includes: intercooler sprayer bar, all necessary hoses and fittings, switch, and wiring kit. Includes 10 lB bottle. Retail: $499.00
$415.98The gas (we suggest CO2) sprays directly on your intercooler to lower the intercooler temp to well below freezing. The result is a tremendous drop in intake temperatures. Dyno tests have seen increases of over 50+ horsepower! Allows you to cool of your Intercooler in between races, to allow for a more efficient setup and increasing HP. Kit includes: intercooler sprayer bar, all necessary hoses and fittings, switch, and wiring kit. no bottle included. Retail: $399.00
$299.80Black__ The PERRIN cold air intake system is designed for power. Manufacturing one of the only properly positioned and sized MAF sensor adaptors for the WRX, Perrin intakes are able to achieve higher horsepower numbers then our competitors.
PERRINâ„¢ intake systems use colorful silicone tubing to dress up the engine bay and fight heat soak. Flexible silicone tubes make installation easy and prevent wear damage at contact points. Kit includes two silicone intake tubes, PERRINâ„¢ foam air filter, MAF sensor housing, mounting hardware.
$249.90Perrin's Radiator Shroud is designed to push more air through your radiator, making your WRX run much colder. When your vehicle is motion, air goes through the grill and is pushed across the radiator. Some air escapes around the top and bottom, limiting the efficiency of the radiator. Perrin's shroud fits over the top of the core support and radiator, limiting the amount of air that escape. This simple bolt on will increase performance and add to your vehicle's looks. Features a Perrin logo that is strategically placed over the core support to allow the color of your WRX to shine through. Fits all 02+ WRX models, including STi.
$54.90Brand new front mount intercooler for your 2002-2005 Subaru WRX and STI is now available from TurboXS. Very affordable and efficient for your high horsepower cars. This front mount is much larger then the original TXS kit. It bolts on with no cutting except to fit the front bumper. In additional this new FMIC includes a TurboXS blow off valve.
The intercooler kit does require a short ram intake which can be purchased from us.
The TurboXS Subaru WRX and STI front mount intercooler kit includes:
-Front Mount Intercooler Core
-Front Bumper Support Beam
-Intercooler Piping Kit
-T bolt Clamps
-Radiator Overflow Bottle
-TXS RBV34 By Pass Valve
-Fuel Line Hose
Fits: 02-05 WRX & STi
Short ram intake include billet aluminum MAF adapter, K&N pod filter, and mounting bracket. The TurboXS intake is engineered to maintain the correct mass air flow sensor signal leading avoiding some of the problems associated with running improperly designed intakes.
$143.00The TXS TMIC for the Subaru Forester XT utilizes the same core as our highly regarded WRX TMIC. However, we have modified the mounting system to allow installation into the Forester XT. The much larger core volume reduces the pressure drop across the IC while the bar and plate core design improves the cooling efficiency. Comes complete with replacement silicone Y piece and stainless steel T-bolt clamps.
NOTE: WRX TMIC shown in picture. FXT model is same core with slightly different Silicone Y-piece.
$750.00Utilizing the largest bar and plate core we could fit under the hood, the TXS TMIC is over 2 times the volume of the stock TMIC. The larger volume reduces the pressure drop across the IC while the bar and plate core design improves the cooling efficiency. Comes complete with replacement silicone Y piece and stainless steel T-bolt clamps.
$721.00When massive flow and cooling is needed, the Turbo XS Front Mount Intercooler delivers. Dwarfing the factory IC core volume by more than 3.3 times, the TurboXS Front Mount Intercooler bar and plate core is larger AND less restictive at high flow rates resulting in better cooling performance.
NOTE: A Short Ram is required to install the WS-FMIC.
The Kit Includes:
Front Mount Intercooler Core
Front Bumper Support Beam
Intercooler Piping Kit
Silicone Couplers
Stainless Steel T bolt Clamps
Radiator Overflow Bottle
TXS RBV34 Bypass Valve
Fuel Line Hose
Direct replacement for factory hose. Made of high temp silicone. Eliminates restriction in factory hose.
$85.00I LOVED THE SERVICE YOU GUYS GAVE ME WITH MY NEW WASTE GATE! TRULY HELPFUL AND GENEROUS. LOOK FORWARD TO BUYING MORE.
- Sheryl P. CasulA, Australia...
Read More ->
I called and placed my order over the phone. I had a bunch of questions and the lady was kind and very helpful. She made sure I got all the right......
Read More ->
Garrett 40mm GVW-40 External Wastegate K...
Garrett 40mm GVW-40 External Wastegate K...
© Copyright 2005-2023 Himni Racing. All Rights Reserved.