TiAL 38mm External Wastegate Gasket fits TiAL 35mm, 38mm, F38 2 Bolt waste gates & Turbonetics Deltagate. Reusable & made of stainless steel. Very durable & does not blow out like other gaskets. Used on both gate inlet (manifold side) & outlet. (dump tube side)
Material: Stainless Steel
Reusable?: Yes
Seal Type: Extreme heat rolled-lip
TiAL 46mm (F46) External Wastegate Gasket, 4 Bolt, Reusable & made of stainless steel. Very durable & does not blow out like other gaskets. Used on both gate inlet (manifold side) & outlet. (dump tube side)
Material: Stainless Steel
Reusable?: Yes
Seal Type: Extreme heat rolled-lip
Genuine Tial Replacement mounting clamp for all Tial BOV's including 50mm, Q & QR blow off valves.
$39.90Tial BOV blow off valve Spring. Made by Tial and used to change out the spring pressure on the Tial BOV's to affect the BOV response to reduce comprssor surge (different spring levels affect the amount of vacuum required on each engine to open the BOV on throttle release)
Use the cart below to select the proper BOV spring for your application.
Engine Vacuum Reading Between_____/__ Color ____/____Use Spring
-22 & -23 in/Hg ___________________ Pink ___________ -12 psi (-24 in/Hg)
-18 & -21 in/Hg ___________________ Un-painted_______-11 psi (22 in /Hg)
-14 & -17 in/Hg ___________________ White ___________ -9 psi (22 in/Hg)
-10 & -17 in/Hg ___________________ Black ____________ -7 psi (14 in/Hg)
Note::: Measure engine vacuum at idle while at operating temperature
$32.70TiAL steel Mounting Flange for all TiAL Blow Off Valves/BOV's. Available in standard mild steel & SS. Chip-cut allows the flange to mount flush to intercooler tube/pipes. Weld on for use with steel tubes.
Fits All BOV's including:
50mm, Q, QR, Alpha Q, etc.
Genuine TiAL billet Aluminum Weld-On Mounting Flange for all TiAL Blow Off Valves/BOV's. Chip-cut allows the flange to mount flush to intercooler tube/pipes. Weld on for use with aluminum tubes.
Fits All BOV's including:
50mm, Q, QR, Alpha Q, etc.
This item is normally in stock & ships within 1-72 hours.
Tial Q BOV (Blow Off Valve) Pick your color & mounting flange. Use the stainless steel flange for steel & stainless pipe & pick aluminum for aluminum pipes. Complete kits comes with everything.
This item is normally in stock & ships with 1-72 hours.
- Full BOV kit Includes:
(x1)Tial Q BOV (your choice of color)
(x1)Aluminum mounting clamp with bolt
(x1)Banjo air fitting with bolt, washers & Viton O-ring
- Select your mounting flange adapter from menu. Options are:
Aluminum Tube Weld Flange
Steel Tube Weld Flange
Tial TO Greddy bolt on Adapter (allows Tial BOV to bolt on to GReddy BOV flange)
Tial TO HKS bolt on Adapter (allows Tial BOV to bolt on to HKS BOV flange)
Tial to 1.00" Slip On Hose Adapter
Tial to 1.25" Slip On Hose Adapter
Tial to 1.50" Slip On Hose Adapter
For use on turbo-charged and super-charged applications (Paxton, Vortec, etc.). The body and all internal components are CNC-machined from 6061 aluminum alloy. It features a large 1.98 in (50.5mm) valve.
The V-Band design aluminum mounting clamp gives a very clean and unique appearance. The clamp is anodized and uses Stainless Steel hardware for a long lasting, corrosion-free appearance.
The valve seal utilizes a Viton O-ring that is clamped in place to prevent the possibility of sticking to the seat and pulling out. The valve stem and guide are Teflon-lubricated, hard anodize-coated for wear resistance.
The Blow Off Valve also comes with Tial's own machined aluminum banjo-type air fitting and bolt, with over sized 10mm hose barb for quick actuator response. The actuator has a high temp silicone Nomex-reinforced diaphragm for long life.
Through countless hours of R&D we were able to make the same size valve flow a staggering 60% more than the original design - that means 60% more air is blown off per cycle! This is the highest flowing BOV on the market.
$235.00This item is normally in stock & ships within 1-72 hours.
TiAL QR Recirculating Blow Off / bypass Valve (BOV) is a recirculated version of the TiAL Q BOV with the added ability to recirculate the air back to the intake. Uses the same mounting v-band flange as the all the other TiAL BOV's with GReddy & HKS adapter/converter flanges also available (select flange type from menu) Full kit includes everything needed to install & includes air fittings, o-ring, clamp, hardware, etc.
This item is normally in stock & ships with 1-72 hours.
- Color: Your choice of Red, Blue, Silver, Black, or Purple.
- Flange: Your choice of Aluminum Weld Flange, Steel Weld Flange, GReddy bolt on adapter flange, or HKS Bolt on adapter flange.
- Recirculating Size: Your choice of Recir (outlet) hose connection diameter
Note: The Greddy & HKS adapter flanges are used to allow the Tial BOV to direct bolt on to an existing Greddy or HKS BOV flange.
$236.00TIAL QRJ BOV is the latest boost control valve is designed with the needs of high performance recirculating systems in mind. The QRJ features a new body design, compact installation envelope, high-flow capacity, and configurable inlet and outlet ports.
This item is normally in stock & ships with 1-72 hours.
- Full BOV kit Includes:
(x1)Tial QRJ BOV (your choice of color)
(x1)Aluminum mounting flanges (select from menu)
(x1)Banjo air fitting with bolt, washers & Viton O-ring
- Select your mounting flange adapter from menu. Options are:
No Flanges
1.00" Hose Mounting flanges (inlet/outlet)
1.50" Hose Mounting flanges (inlet/outlet)
- For use on turbo-charged and super-charged applications (Paxton, Vortec, etc.) The body and all internal components are CNC-machined from 6061 aluminum alloy. It features a large 1.50 in (38.5mm) valve.
- Optional configurations of Hose and or V-band connections for the inlet and outlet ports.
- Valve seal utilizes a Viton O-ring that is clamped in place to prevent the possibility of sticking to the seat and pulling out. The valve stem and guide are Teflon-lubricated, hard anodize-coated for wear resistance.
- comes with our own machined aluminum banjo-type air fitting and bolt, with over sized 10mm hose barb for quick actuator response.
- Color anodized aluminum options (Silver, Red, Blue, Purple, Black).
- Multiple inlet and return port options for many install configurations.
- Internal return spring pressure tuned for fastest response. Custom spring options are available for other configurations.
TiAL stainless steel .52 A/R V-band turbine/exhaust housing for the following turbos using a 76 trim 53.9mm turbine wheel:
Garrett GT28RS, GT2860RS, GT2871R, GT2876R, GTX2860R, GTX2863R, GT2867R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2-3 A/R options for each turbo.
$349.00TiAL stainless steel .64 A/R V-band turbine/exhaust housing for the following turbos using a 76 trim 53.9mm turbine wheel:
Garrett GT28RS, GT2860RS, GT2871R, GT2876R, GTX2860R, GTX2863R, GT2867R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2-3 A/R options for each turbo.
$374.00TiAL stainless steel .86 A/R V-band turbine/exhaust housing for the following turbos using the 76 trim 53.9mm turbine wheel:
Garrett GT28RS, GT2860RS, GT2871R, GT2876R, GTX2860R, GTX2863R, GT2867R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$349.00Select Spring Pressure & color from menu.
The most commonly used TiAL wastegate. Has heavy duty 347 SS alloy used in valve and valve housing. 17-7 PH SS actuator spring and high temperature silicone Nomex reinforced actuator diaphragm gives rock solid boost stability. Has superior product life under the most demanding conditions. (Turbo rotary applications 2000F (1093C) exhaust temperatures, etc.)
Comes complete with:
TiAL 38mm Wastegate
Valve seat (Inlet sealing ring)
10mm banjo air fittings
Gaskets
Stainless steel hardware.
Other Features include::
High temperature silicone Nomex reinforced actuator diaphragm rated to 4 Bar
17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resists "relaxing" at high temperatures
- Nitronic 60 Stainless Steel is used for the valve seat, valve bushing, and lower housing fastening hardware.
Note:: The water cooling on the Tial MVR is not a mandatory hook up. Only an added available option if you want to use liquid cooling.
This MV-S-A 38mm unit is designed specifically for motorsport applications that can't utilize the water cooling ports on the standard MV-S wastegate. The MV-S-A or "long neck" / "tall boy" has the standard 38mm valve but also has five heat fins that separate the casting from the actuator top. Born into the world of Motorsport this wastegate can handle the harshest of conditions and give 100% performance 100% of the time. It is the choice wastegate of many WRC teams. Your Choice of Polished Silver, Red, Blue, Black or Purple.
Included with every Tial MV-S-A:
- MV-S-A wastegate Assembly
- 2 TiAL -4 AN removable water fittings
- MV-S Valve Seat
- Inlet V-band clamp & Flange
- Outlet V-Band Clamp & Flange
- 2 TiAL Air Fittings
- Plugs for unused air ports
- Extra actuator springs
- High temp NiCrFe based alloy is used for valve and 347SS valve housing will offer longer product life compared to competing designs.
- High temperature silicone Nomex reinforced actuator diaphragm.
- 17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resist "relaxing" at temperature to 900F (483C).
- Nitronic 60 Stainless Steel is used for the valve seat, and valve bushing.
- All Stainless Steel hardware.
- Mating weld flanges are 304L
- Color anodized aluminum actuator (Silver, Red, Blue, Purple, Black).
- 3 lower ports and two top ports for easy install, no need to rotate the actuator top at all, plugs included for unused ports.
- V-Band inlet and outlet make install easy, flanges and clamps are in the box
- Integrated -4 AN water cooling ports that cycle a small amount of coolant through the actuator top to keep the temperatures down in extreme conditions such as road racing. These are leak tested after installation from the factory and can be removed if not utilized.
- Five heat sinks raise the actuator top away from the casting to dissipate heat when water cooling can not be used
- Designed for Motorsport/Road Racing
::: NOTE:: Select Spring Pressure & color from menu.
$410.00
This is the TiAL stainless steel .63 A/R V-band turbine/exhaust housing for the following turbos with 60mm, 84 trim turbine wheel:
Garrett GT3071R, GT3076R, GT30R, GTX3071R, GTX3067R, GTX3076R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$399.00This is the TiAL stainless steel .82 A/R V-band turbine/exhaust housing for the following turbos with 60mm, 84 trim turbine wheel:
Garrett GT3071R, GT3076R, GT30R, GTX3071R, GTX3067R, GTX3076R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$399.00This is the TiAL stainless steel 1.06 A/R V-band turbine/exhaust housing for the following turbos with 60mm, 84 trim turbine wheel:
Garrett GT3071R, GT3076R, GT30R, GTX3071R, GTX3067R, GTX3076R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$399.00Note:: The water cooling on the Tial MVS is not a mandatory hook up. Only an added available option if you want to use liquid cooling.
The TiAL MV-S (aka V38) external wastegate has the same flow capability as the standard Tial 38mm (F38) wastegate but with V-band inlet & outlet mountng. With it's new compact design, fitment into tight spaces is no longer a issue. The V-band mounting found on the new V38 (And V44/V60) provides maximum positioning possibilities & allows the wastegate to be installed & removed quickly & easily, in needed. It can be rotated 360 degrees to any position that suits your needs. Another advantage is that it does not require the use of gaskets. Just like the rest of the TiAL product line, it comes with their legendary performance & reliability. Your Choice of Polished Silver, Red, Blue, Black or Purple.
Has heavy duty 347 SS alloy used in valve and valve housing. 17-7 PH SS actuator spring and high temperature silicone Nomex reinforced actuator diaphragm gives rock solid boost stability. Has superior product life under the most demanding conditions. (Turbo rotary applications 2000F (1093C) exhaust temperatures, etc.)
Comes complete with:
TiAL V38 38mm V-band Wastegate (Your Choice of color)
Valve seat (Inlet sealing ring) - Stainless Steel
V-band Inlet & Outlet Flanges- Stainless Steel
V-band Inlet & Outlet Clamps - Stainless Steel
Air fittings & block off plugs.
Stainless steel hardware.
High temperature silicone Nomex reinforced actuator diaphragm rated to 4 Bar
17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resists "relaxing" at high temperatures
- Nitronic 60 Stainless Steel is used for the valve seat, valve bushing, and lower housing fastening hardware.
Compact Design
Leak-Free V-Band mounting (no gaskets needed)
::: NOTE:: Select Spring Pressure & color from menu.
$299.00This is the TiAL stainless steel .63 A/R V-band turbine/exhaust housing for the following turbos with 68mm 84 trim turbine wheel:
Garrett GT35R, GT3582R, GTX3576R, GTX3582R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$433.00This is the TiAL stainless steel .82 A/R V-band turbine/exhaust housing for the following turbos with 68mm 84 trim turbine wheel:
Garrett GT35R, GT3582R, GTX3576R, GTX3582R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$433.00This is the TiAL stainless steel 1.03 A/R V-band turbine/exhaust housing for the following turbos with 68mm 84 trim turbine wheel:
Garrett GT35R, GT3582R, GTX3576R, GTX3582R
Flange sizes: 2.125" OD Inlet, 3.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$433.00Note:: The water cooling on the Tial MVR is not a mandatory hook up. Only an added available option if you want to use liquid cooling.
The new TiAL MV-R 44mm external wastegate has the same flow capability as the standard Tial 44mm (V44) wastegate but in a new lighter weight more compact size. Fitment into very tight spaces is now posable & get this.... it's water cooled too! It comes with water ports that flow a small amount of water through the actuator top to keep the temperatures down in extreme conditions such as road racing & rotary engines. However, the wastegate may also be used without the water cooling if your application doesn't need it. (water port plugs included)
The 44mm MV-R is completely interchangeable with Tial's standard 44mm V44 allowing it to be installed to any application where a V44 was normally used.
The V-band mounting found on the new 44mm MVR provides maximum positioning possibilities & allows the wastegate to be installed & removed quickly & easily if needed. It can be rotated 360 degrees to any position that suits your needs & does not require the use of gaskets. Just like the rest of the TiAL product line, it comes with their legendary performance & reliability. Your Choice of Polished Silver, Red, Blue, Black or Purple.
Has heavy duty 347 SS alloy used in valve and valve housing. 17-7 PH SS actuator spring and high temperature silicone Nomex reinforced actuator diaphragm gives rock solid boost stability. Has superior product life under the most demanding conditions. (Turbo rotary applications 2000F (1093C) exhaust temperatures, etc.)
Comes complete with:
TiAL MV-R V-band Wastegate (Your Choice of color)
Valve seat (Inlet sealing ring) - Stainless Steel
V-band Inlet & Outlet Flanges- Stainless Steel
V-band Inlet & Outlet Clamps - Stainless Steel
Air fittings
Plugs included for unused air ports
Stainless steel hardware.
High temperature silicone Nomex reinforced actuator diaphragm rated to 4 Bar
17-7 PH Stainless Steel actuator spring gives consistent pressure at high temperature, resists "relaxing" at high temperatures
- Nitronic 60 Stainless Steel is used for the valve seat, valve bushing, and lower housing fastening hardware.
Compact Design
Leak-Free V-Band mounting (no gaskets needed)
::: NOTE:: Select Spring Pressure & color from menu.
$367.90It's here! The V60 is TiAL's largest wastegate with a Huge 60mm design. This wastegate utilizes all of the high quality materials & manufacturing that has made Tial products legendary. The gate uses a interlocking V-band inlet & outlet that requires no use of gaskets, while still providing a leak-free seal. As with all the Tial wastegates, it will reliably control boost even under the most extreme conditions. The V60 is a perfect choice for use with high boost, big turbo applications.
Comes With Everything Needed:
V60 (60mm) Wastegate (select color)
Inlet & Outlet stainless steel V-Band Flanges
Inlet & Outlet stainless steel V-Band Clamps
Stainless Steel Valve Seat
2 Air / Hose Fittings with copper washers
Installation Instructions
This is the TiAL stainless steel 1.00 A/R V-band turbine/exhaust housing for the following turbos with 82mm 84 trim turbine wheel:
Garrett GT42, GT42R, GT4294R, GT4202R, GT42RS, GTX4294R, GTX4202R
Flange sizes: 2.75" OD Inlet, 4.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$730.00TiAL stainless steel 1.30 A/R V-band turbine/exhaust housing for the following turbos with 82mm 84 trim turbine wheel:
Garrett GT42, GT42R, GT4294R, GT4202R, GT42RS, GTX4294R, GTX4202R
Flange sizes: 2.75" OD Inlet, 4.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$730.00Wastegate spring for use with:
Tial 35mm, 38mm (F38 w/ 2 bolt flange),
Tial 44mm V44 (old school discontinued 44mm wastegate with large top hat)
Tial 46mm F46 (4 bolt flange w/ large top hat)
Tial 60mm V60 (largest Tial gate)
"Small" Tial Wastegate Springs. Choose Small Red, Small Yellow, Small Green, or Small Blue. Can be combined with the TiAL "Big" springs to reach desired boost pressure.
::Note:: Below is a cart for you to use as a reference in selecting the proper spring for your particular size Tial wastegate. (though the springs don't very, how they react in a given size wastegate does)
Tial 35mm, 38mm (F38) & 41mm (F41) Wastegates:
Small Yellow = .25 bar (3.63 psi)
Small Red = .4 bar (5.80 psi)
Small Green = .5 bar (7.25 psi)
Small Blue = .6 bar (8.70 psi)
Tial 44mm (V44), 46mm (F46) & 60mm (V60) Wastegates:
Small Yellow = .2 bar (2.90 psi)
Small Red = .3 bar (4.35 psi)
Small Green = .4 bar (5.80 psi)
Small Blue = .5 bar (7.25 psi)
This is the TiAL stainless steel 1.16 A/R V-band turbine/exhaust housing for the following turbos with 82mm 84 trim turbine wheel:
Garrett GT42, GT42R, GT4294R, GT4202R, GT42RS, GTX4294R, GTX4202R
Flange sizes: 2.75" OD Inlet, 4.00" OD Outlet (use only TiAL genuine flanges)
The TiAL SS are rare, hard to get housings but we try to keep them on hand when possible. They are made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 3 A/R options for each turbo.
$730.00Wastegate spring for use with:
Tial 35mm, 38mm (F38 w/ 2 bolt flange),
Tial 44mm V44 (old school discontinued 44mm wastegate with large top hat)
Tial 46mm F46 (4 bolt flange w/ large top hat)
Tial 60mm V60 (largest Tial gate)
"Big" Tial Wastegate Springs. Choose Big Red, Big Yellow, Big Green, or Big Blue. Can be combined with the TiAL "Small" springs to reach desired boost pressure.
::Note:: Below is a cart for you to use as a reference in selecting the proper spring for your particular size Tial wastegate. (though the springs don't very, how they react in a given size wastegate does)
Tial 38mm (F38) & 41mm (F41) Wastegates:
Big Yellow = .7 bar (10.15 psi)
Big Red = .8 bar (11.60 psi)
Big Green = .9 bar (13.05 psi)
Big Blue = 1 bar (14.50 psi)
Tial 44mm (V44), 46mm (F46) & 60mm (V60) Wastegates:
Big Yellow = .6 bar (8.70 psi)
Big Red = .7 bar (10.15 psi)
Big Green = .8 bar (11.60 psi)
Big Blue = .9 bar (13.05 psi)
Tial Waste gate Springs for use with: TiAL 38mm MVS (V-band 38mm wastegate) TiAL 44mm MVR (compact 44mm wastegate)
Not for use w/ with the older style standard Tial gates (2 bolt flange F38, 4 bolt flanged 41 & 46mm, V-band V44 w/ large top hat) These springs are used to change the amount of boost pressure your turbo produces. Pick your spring or spring combination based on the amount of boost you want your engine to see.
Spring Pressures for MVS (V38) Application
SPRING COMBINATIONS
BAR_________PSI_____Color
0.3 ________4.35 ___BROWN
0.4 ________5.80 ___GOLD
0.5 ________7.25 ___BIEGE
0.6 ________8.70 ___GREY
0.7 ________10.15 __GOLD + BROWN
0.8 ________11.60 __COPPER + BROWN
0.9 ________13.05 __GREY + BROWN
1.0 ________14.50 __GREY + GOLD
1.1 ________15.95 __MAROON + BEIGE
1.2 ________17.40 __COPPER + MAROON
1.3 ________18.85 __GREY + GOLD + BROWN
1.4 ________20.30 __COPPER + MAROON + BROWN
1.5 ________21.75 __GREY + MAROON + BROWN
1.6 ________23.20 __COPPER + MAROON + BEIGE
1.7 ________24.66 __GREY + MAROON + BEIGE
Spring Pressures for MVR (NEW 44MM) Application
SPRING COMBINATIONS
BAR ____PSI ____Color
0.3 ____4.35 ___GOLD
0.4 ____5.80 ___MAROON
0.5 ____7.25 ___BROWN + GOLD
0.6 ____8.70 ___BROWN + MAROON
0.7 ____10.15 __GREY + GOLD
0.8 ____11.60 __GREY + MAROON
0.9 ____13.05 __BROWN + GOLD + GREY
1.0 ____14.50 __BROWN + MAROON + GREY
1.1 ____15.95 __BEIGE + GOLD + GREY
1.2 ____17.40 __MVR PLAIN + COPPER + GOLD + BROWN
1.3 ____18.85 __MVR PLAIN + COPPER + MAROON + BROWN
1.4 ____20.30 __MVR PLAIN + GREY+ GOLD + BEIGE
1.5 ____21.75 __MVR PLAIN + GREY + MAROON + BEIGE
This is the Tial V-band INLET clamp (manifold side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT28R, GT28RS, GT2871R, GT2876R, GT3071R, GT3076R, GT30R, GT3040R, GT3082R, GT3582R, GT35R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$39.90This is the Tial V-band INLET clamp (manifold side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT40R, GT4088R, GT4094R, GT42R, GT4294R, GT42RS, GT4202R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$37.99This is the Tial V-band OULET clamp (downpipe side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT28R, GT28RS, GT2871R, GT2876R, GT3071R, GT3076R, GT30R, GT3040R, GT3082R, GT3582R, GT35R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$39.90This is the Tial V-band OUTLET clamp (downpipe side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT40R, GT4088R, GT4094R, GT42R, GT4294R, GT42RS, GT4202R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$37.99This is the original V-band clamp used to connect/join the turbine/exhaust housing TO the center cartridge (CHRA) on the Garrett GT42R frame turbos. Genuine Garrett factory part, made of stainless steel & includes high heat lock nut. Fits: GT42, GT42R, GT4294, GT4294R, GT4202, GT4202R, GTX42, GTX42R, GTX4294R, GTX4202R
Note: This is not the clamp used for connection of the downpipe to the turbo. That part number is R15A014.
$37.00TiAL threaded INLET (MANIFOLD SIDE) 38mm 2 bolt external waste gate mounting flange. Commonly used for making custom exhaust manifolds, etc. Available in your choice of mild or stainless steel.
- Brand: TiAL
- Application: Manifold / wastegate INLET side. (not outlet/ dump tube side)
- Fitment: Tial 35mm, 38mm external wastegate & Turbonetics Deltagate.
- Flange Side #1: Smooth flat face.
- Flange Side #2: Recessed groove for pipe/tube alinement & welding.
- Bolt Pattern: 2 Bolt threaded w/ 8mm x 1.25 thread size.
- Material Type: Mild Carbon Or Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL drilled OUTLET (Dump Tube Side) 38mm 2 bolt external waste gate mounting flange. Used for mounting an outlet/dump tube/"screamer pipe" to the outlet side of the waste gate. Available in your choice of mild or stainless steel.
- Brand: TiAL
- Application: Dump tube / wastegate OUTLET side.
- Fitment: Tial 35mm, 38mm external wastegate & Turbonetics Deltagate.
- Flange Side #1: Smooth flat face.
- Flange Side #2: Recessed groove for pipe/tube alinement & welding.
- Bolt Pattern: 2 Bolt drilled though for use w/ 8mm bolts/studs.
- Material Type: Mild Carbon Or Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
This is the Tial V-band INLET flange (manifold side) for use with Tial stainless steel v-band turbine housing ranging from GT28R-GT35R frame sizes. Made of 304 stainless steel.
Fits the TiAL SS housings for the following turbos:
GT28, GT28R, GT2560R, GT28RS, GT2860RS, GT2871R, GT25/40R, GT2876R, GTX28R, GTX2860R, GTX2863R, GTX2867R, GT3071, GT3071R, GTX3071R, GT30R, GT3076R, GTX3076R, GT3040, GT3040R, GT3082R, GTX3067R, GTX3576R, GT35, GT35R, GT3582R, GTX35, GTX35R, GTX3582R etc.
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their clamps. (used to connect the flanges to the housing)
$48.50This is the Tial V-band OUTLET flange (downpipe side) for use with Tial stainless steel v-band turbine housing. Made of 304 stainless steel.
Fits the TiAL SS housings for the following turbos:
GT28, GT28R, GT2560R, GT28RS, GT2860RS, GT2871R, GT25/40R, GT2876R, GTX28R, GTX2860R, GTX2863R, GTX2867R, GT3071, GT3071R, GTX3071R, GT30R, GT3076R, GTX3076R, GT3040, GT3040R, GT3082R, GTX3067R, GTX3576R, GT35, GT35R, GT3582R, GTX35, GTX35R, GTX3582R etc.
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their clamps. (used to connect the flanges to the housing)
$48.50This is the Tial V-band INLET flange (manifold side) for use with Tial stainless steel v-band turbine housing. Made of 304 stainless steel.
Fits the TiAl SS turbine/exhaust housings for the following turbos:
GT42, GT42R, GT4294R, GT42RS, GT4202R, GTX4294R, GTX4202R, GT45, GT45R, GT4508, GT4508R, GTX45R, GTX45, GTX4508R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their clamps. (used to connect the flanges to the housing)
$68.50This is the Tial V-band OUTLET flange (downpipe side) for use with Tial stainless steel v-band turbine housing. Made of 304 stainless steel.
Fits the TiAl SS turbine/exhaust housings for the following turbos:
GT42, GT42R, GT4294R, GT42RS, GT4202R, GTX4294R, GTX4202R, GT45, GT45R, GT4508, GT4508R, GTX45R, GTX45, GTX4508R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their clamps. (used to connect the flanges to the housing)
$79.00TiAL Stainless Steel INLET (manifold side) V-band clamp for TiAL V38 38mm MVS V-band external wastegate. Used to mount the wastegate to a turbo manifold/header. Includes lock nut & bolt.
- Brand: TiAL
- Application: Tial 38mm MVS wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 38mm V38 MVS V-band external wastegate. Used to mount the V38 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 38mm MVS wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL Stainless Steel Outlet (dump tube side) V-band clamp for TiAL V38 38mm MVS V-band external wastegate. Used to mount the dump tube outlet flange to the waste gate.
- Brand: TiAL
- Application: Tial 38mm MVS wastegate outlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band OUTLET flange for the Tial 38mm V38 MVS external V-band wastegate. Used to mount the outlet dump tube to the V38 waste gate.
- Brand: TiAL
- Application: Tial 38mm MVS wastegate outlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
This is the TiAL stainless steel 1.02 A/R V-band turbine/exhaust housing for the following turbos with the 87mm 85 trim turbine wheel:
Garrett GT45R, GT4508R GTX45R, GTX4508R
Flange sizes: 2.75" OD Inlet, 4.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2 A/R options for each turbo, depending on the turbo.
$729.00This is the TiAL stainless steel 1.15 A/R V-band turbine/exhaust housing for the following turbos with the 87mm 85 trim turbine wheel:
Garrett GT45R, GT4508R GTX45R, GTX4508R
Flange sizes: 2.75" OD Inlet, 4.00" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2 A/R options for each turbo, depending on the turbo.
$729.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 44mm V44 & MVR external wastegates. Used to mount the 44mm wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 44mm V44 & MVR wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band OUTLET flange for the Tial 44mm V44 & MVR external waste gates. Used to mount the outlet dump tube to the 44mm wastegate.
- Brand: TiAL
- Application: Tial 44mm V44 & MVR wastegate outlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL Stainless Steel replacement Inlet (manifold side) V-band clamp for TiAL 44mm V44 & MVR V-band external wastegate. Used to mount the wastegate to an exhaust manifold/header. Includes bolt & lock nut.
- Brand: TiAL
- Application: Tial 44mm V44 & MVR waste gate
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL Stainless Steel replacement Outlet V-band clamp for TiAL 44mm V44 & MVR external wastegate. Used to mount the dump tube outlet flange to the waste gate. Includes lock nut & bolt.
- Brand: TiAL
- Application: Tial 44mm V44 & MVR waste gate outlet
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel 1.15 A/R V-band turbine/exhaust housing for the following turbos with the 111.5mm 84 trim turbine wheel:
Garrett GT55, GT55R, GT5518R, GT5533R, GTX55R, GTX5518R, GTX5533R
Flange sizes: 3.50" OD Inlet, 4.50" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2 A/R options for each turbo, depending on the turbo.
$1,372.00TiAL stainless steel 1.30 A/R V-band turbine/exhaust housing for the following turbos with the 111.5mm 84 trim turbine wheel:
Garrett GT55, GT55R, GT5518R, GT5533R, GTX55R, GTX5518R, GTX5533R
Flange sizes: 3.50" OD Inlet, 4.50" OD Outlet (use only TiAL genuine flanges)
Made of solid stainless steel & utilizes V-band inlet (manifold side) & outlet (downpipe side) The casted then machined stainless steel has a very smooth finish, both inside and out. Does not rust & is about 33% lighter then normal turbine housings. Very strong & withstands the heat with no problem. Mounts to Tial V-band flanges using Tial V-band clamps & doesn't need or use studs/bolts or gaskets. They have a smaller physical overall size but flow like a larger housing. On average, there are 2 A/R options for each turbo, depending on the turbo.
$1,372.00TiAL Stainless Steel Inlet/Outlet Flange for TiAL 46mm wastegate. Used to mount the wastegate to turbo manifold or to mount the oulet dump tube. Does not include gasket.
$29.00TiAL stainless steel V-band INLET mounting flange for the Tial V60 60mm external wastegate. Used to mount the V60 waste gate to turbo exhaust manifold.
Note: No Gaskets are required with vband flanges.
$33.99TiAL stainless steel V-band OUTLET mounting flange for the Tial V60 60mm external wastegate. Used to rout/mount the V60 waste gate dump tube.
Note: No Gaskets are required with vband flanges.
$33.99TiAL Air Fitting Set For Tial 50mm BOV and ALL Tial Wastegates. Includes:: 1 Banjo Fitting, 1 Banjo Bolt & 2 Washers/gaskets.
$19.40Authentic TiAL Stainless Steel Valve Seat / Sealing Ring for the older TiAL 38mm F38 (2 bolt inlet)& TAL 38mm MVS (V38 V-Band) external wastegates. Select your wastegate from the menu. This part goes between the waste gate inlet flange & exhaust manifold to create leek free seal. If your wastegate is missing this item, it will completely destroy the proper function of the waste gate. It is an absolute 'must' part for the gate to function correctly.
$24.95TiAL Stainless Steel external waste gate Valve Seat / Sealing Ring for both of the Tial 44mm v-band wastegate). Goes between the wastegate and inlet flange to create leek free seal.
Select from menu:
For the Older V44 waste gate (has large top hate & no water cooling ports)
For the New MVR waste gate (small top hat with water cooling ports)
Genuine Tial replacement diaphragm for the 38mm 2 bolt flanged waste gate (F38) & V-band 44mm waste gate (V44). Used to replace your old diaphragm that may be worn or damaged. Installs in the external wastegate with little effort & time. A cost effective alternative to replacing the whole gate.
$59.99Genuine Tial replacement diaphragm for the 38mm MVS/MS-S/MVS-A V38 V-band waste gate. Used to replace your old diaphragm that may be worn or damaged. Installs in the external wastegate with little effort & time. A cost effective alternative to replacing the whole gate.
$54.99Genuine Tial replacement diaphragm for the 44mm MVR/MV-R V-band waste gate. Used to replace your old diaphragm that may be worn or damaged. Installs in the external wastegate with little effort & time. A cost effective alternative to replacing the whole gate.
$55.99TiAL Stainless Steel replacement Inlet (manifold side) V-band clamp for TiAL 60mm V60 V-band external wastegate. Used to mount the wastegate to an exhaust manifold/header. Includes bolt & lock nut.
- Brand: TiAL
- Application: Tial 60 V60 waste gate
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL Stainless Steel replacement Outlet V-band clamp for TiAL 60mm V60 external wastegate. Used to mount the dump tube outlet flange to the waste gate. Includes lock nut & bolt.
- Brand: TiAL
- Application: Tial 60mm V60 outlet
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band OUTLET flange for the Tial 60mm V60 external waste gates. Used to mount the outlet dump tube to the 60mm wastegate.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate outlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Garrett 40mm GVW-40 External Wastegate ...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Master engine hardware kit. Replaces mo...
$78.00Master engine hardware kit. Replaces mo...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
For use with All small to mid frame Gar...
$78.00For use with All small to mid frame Gar...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Himni Racing Polyurethane FC RX-7 Motor...
$98.00Himni Racing Polyurethane FC RX-7 Motor...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Made in USA. The Himni Racing FC RX7 St...
$215.00Made in USA. The Himni Racing FC RX7 St...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Himni Racing Polyurethane FD RX-7 Motor...
$99.90Himni Racing Polyurethane FD RX-7 Motor...
$317.00TiAL stainless steel replacement V-band INLET mounting flange for the Tial 60mm V60 external wastegates. Used to mount the v60 wastegate to turbo exhaust manifolds/headers.
- Brand: TiAL
- Application: Tial 60mm V60 wastegate inlet side
- Material Type: Stainless Steel
- Finish: Excellent, Raw, Smooth surface for proper sealing
- Made In: United States (USA)
Master engine hardware kit. Replaces mo...
$84.00Master engine hardware kit. Replaces mo...
$317.00Himni Racing Polyurethane FC RX-7 Motor...
Himni Racing Polyurethane FD RX-7 Motor...
I ordered a Tial blow off valve and it was at my door in only 3 days! The serial number checked out with TiAl as authentic. No one else had the color......
Read More ->
THANK YOU FOR THE EXTREMELY FAST SHIPPING!! HIMNI RACING HAS GREAT PRODUCTS!!
-Eric G. Cape Coral, FL...
Read More ->
Garrett 40mm GVW-40 External Wastegate K...
Garrett 40mm GVW-40 External Wastegate K...
© Copyright 2005-2023 Himni Racing. All Rights Reserved.