Made In The USA::
2" stainless steel v-band clamp for use with our 2" V-band flange and any other 2" v-band flange with 3.00" outer diameter (OD) face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
Most commonly used with v-band flange part number R15S242
$17.90Made In The USA::
2.50" stainless steel v-band clamp for use with our 2.50" V-band flange and any other 2.50" v-band flange with an OD of 3.00" diameter face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
$18.90Made In The USA
3.00" stainless steel v-band clamp for use with our 3.00" V-band flange and any other 3.00" v-band flange with an OD of 3 5/8" - 3 3/4" diameter face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
Fits: 3" V-band flanges with a sealing surface side outer diameter (OD) of 3.62"-3.75" (3 5/8 inch 92mm - 3 3/4 inch - 95mm)
$18.90Made In The USA
3.50" stainless steel v-band clamp for use with our 3.50" V-band flange and any other 3.50" v-band flange with an OD of 4.25" O.D. (108mm) diameter face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
$24.00Made In The USA
4.00" stainless steel v-band clamp for use with our 4.00" V-band flange and any other 4.00" v-band flange with an OD of 4.62"- 4.75" diameter face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
$24.00Made In The USA
5.00" stainless steel v-band clamp for use with our 5.00" V-band flange and any other 5.00" v-band flange with an OD of 5 1/8" O.D. (130.9mm) diameter face/seal side. Extremely high quality & durable. Comes with high heat lock nut. Ideal for matting a v-band flanged downpipe to a v-band turbine housings to V-band to V-band connection. Very strong clamp that withstands high heat without loosing its hold.
$21.50This is the Tial V-band INLET clamp (manifold side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT28R, GT28RS, GT2871R, GT2876R, GT3071R, GT3076R, GT30R, GT3040R, GT3082R, GT3582R, GT35R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$39.90This is the Tial V-band INLET clamp (manifold side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT40R, GT4088R, GT4094R, GT42R, GT4294R, GT42RS, GT4202R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$37.99This is the Tial V-band OULET clamp (downpipe side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT28R, GT28RS, GT2871R, GT2876R, GT3071R, GT3076R, GT30R, GT3040R, GT3082R, GT3582R, GT35R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$39.90This is the Tial V-band OUTLET clamp (downpipe side) for use with Tial stainless steel v-band turbine housing & flange. Used to connect the flange to the turbine housing. Made of stainless steel. Fits the Tial SS v-band housings/flange for the following turbos: GT40R, GT4088R, GT4094R, GT42R, GT4294R, GT42RS, GT4202R
The Tial stainless housings use 2 different v-band connections. One for the inlet (manifold side) & one for the outlet (downpipe side) We have both available, along with their flanges.
$37.99This is the large V-band clamp used to connect/join the compressor housing/cover (cold side) TO the center cartridge (CHRA) on the Garrett GT42R frame turbos. Genuine Garrett factory part, made of stainless steel & includes high heat lock nut. Fits: GT42, GT42R, GT4294, GT4294R, GT4202, GT4202R, GTX42, GTX42R, GTX4294R, GTX4202R
Note: This is not the clamp used for connection of the downpipe to the turbo. That part number is R15A014.
$34.50This is the original V-band clamp used to connect/join the turbine/exhaust housing TO the center cartridge (CHRA) on the Garrett GT42R frame turbos. Genuine Garrett factory part, made of stainless steel & includes high heat lock nut. Fits: GT42, GT42R, GT4294, GT4294R, GT4202, GT4202R, GTX42, GTX42R, GTX4294R, GTX4202R
Note: This is not the clamp used for connection of the downpipe to the turbo. That part number is R15A014.
$37.00Made in The USA. High quality Clampco 2.00" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 2.25" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 2.50" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 2.75" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 3.00" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 3.25" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 3.50" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 3.75" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 4.00" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 4.25" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 4.50" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90Made in The USA. High quality Clampco 5.50" Stainless Steel T-Bolt clamp w/lock nut. Used to connect intercooler couplers to intercooler pipes/tubes, exhaust slip joints, etc. Superior to standard "screw" clamps, does not cut & mar silicone couplers, increased clamping force withstands high pressure applications, applies full 360 degree pressure for a secure fit.
::Note:: When choosing a T-bolt clamp for use with silicone I/C coupler connections, always go up at least one size above the outer diameter of the intercooler tube, to compensate for the thickness of silicone connector. (i.e. 3.00" OD pipe with coupler installed, use a 3.25" or 3.50" Clamp)Some couplers are thinker than others depending on coupler ply/layers. When in doubt, always go up TWO sizes to be safe.
$5.90I can't thank Himni enough for your awesome customer service and technical help. The turbo parts fit perfect. My new favorite turbo shop!
- Chris Y.......
Read More ->
very fast shipping for international!!!! thank you & i will be back for more soon.
-Michael E. Rattelsdorf, Germany...
Read More ->
Garrett 40mm GVW-40 External Wastegate K...
Garrett 40mm GVW-40 External Wastegate K...
© Copyright 2005-2023 Himni Racing. All Rights Reserved.